CGDI BMW FEM BDC Version Not Supported Solution

Dear CGDI Prog BMW Programmer users: During the past days, some locksmiths feedback that when they click on “FEM /BDC key matching”, they receive a prompt “FEM BDC Version is not supported, please upgrade FEM /BDC first”, if you have the same problem, please follow this guide to solve it.

Please upgrade FEM /BDC first”, please Check the BTLD version, If it is 82 or 83 , you need to go to program page .advanced mode , program it (in this article). If it is other version , you need to go to program page, program it with default version (will make a manual ).

 

Choose BDC_Body, then “Advanced mode”.

Follow the prompt ” The ECU is about to be programmed. Please ensure that the car battery has enough power and keep the device cable connected during the programming process. Click on “Yes” to continue.

 

Click on “Yes” to backup the coded data.

The progress will be displayed in the box.

 

Next is BMW F series programming version selection, please choose “BTLD-80”, the next one is to choose “SWFL -80”.

Then click on “Confirm”.

Retrieving and downloading the list of programming files from the server, please be patient, how much time to cost, it will depend on your internet speed.

When it shows 100%, you will be asked to enter VIN 17 characters.

 

Ready to program ECU…It will take about 8 minutes.

When it shows 100%, it means ECU programming successfully.

 

Note 1. If you have not coded after programming, please use the “BMW F/G system Coding” function to code. Some modules (such as gateways) do not require coding and you can ignore this step.

Note 2. If the airbag, sunroof and window are abnormal, please use the “ECU initialization” function to initialize.

Then check it in the Add Key page, it can work now.

 

CGDI BMW Key Programmer tech support: www.obdii365.com

 

CG Keys Not Read or Written to CGDI MB DIY Solution

The last batch of CG keys was not read or written to the CGDI MB. The manufacturer CGDI MB recommends replacing the IR receiver and transmitter.

 

 

Here's the customer's good working experience on solving this issue.

There was neither time nor desire to buy it and wait. Therefore, I tried to install the IR receiver and transmitter from an old faulty original key. Now CGDI MB reads and writes perfectly again !!!

Regular keys labeled CG. Of the five keys, only one key was recorded from the fifth time. After replacing IR light and photo diodes, the keys can be read and written without problems.

http://www.key-programmer.org/2021/01/12/solved-cgdi-keys-not-read-or-written-to-cgdi-mb/

AT-200 Programmer Software Update to V1.8.2

CG AT-200 ecu programmer & ISN code reader released newest software V1.8.2 (2020.12.29).

1.Added MED17/EDC17 Data processing tools(Audi/Seat/Skoda/Volkswagen(VW) 4,5 generation anti-theft) engine data analysis modification

4 generation data：VIN, CS, Status, Anti-theft, MAC, PIN

5 generation data：VIN, CS

2.Added Audi/Seat/Skoda/Volkswagen(VW)/Porsche EGS clone models:

DL382(TC1784), DL501(TC1766), DQ250(TC1766): read and write DFLASH, EXT DFLASH, PFLASH

3. Added ECU(Mini)read and write ISN, VIN: MED17.2, MEV17.2.2, MEVD17.2.2

4. Added ECU(Audi, Citroen, Mg, Seat, Skoda, Volkswagen(VW)) read and write VIN:

MED17.1, MED17.5.5

5. Fix some bugs and optimize software performance

 

 

Free download AT200 V1.8.2

https://mega.nz/file/vT4m0ThQ 

CGDI BMW Software V3.2.0 Adds Porsche 2M25J

 CGDI Prog BMW software update to V3.2.0.

CGDI BMW V3.2.0  NEW

(2020.12.29)

1. Software interface optimization and upgrade

2. Porsche Key Learning added 2M25J chip Learning：Read basic information, Key learning, Load EEPROM

3. CAS4 Key Match(OBD) added "Repair remote key intelligence"

4. Key Match process and display optimization

5. BMW data Repair process optimization

6. Fix some bugs and optimize software performance

CGDI MB Reset Benz 7G EGS TCU

 

CGDI Prog MB is possible to reset/erase Mercedes-Benz 722.9 7g TCU Transmission Control Unit.  Check step-by-step instructions below:

 

Run CGDI MB software

Select Auto Commuter function
Select engine type: TCU

Check wiring diagram
Follow diagram to connect cgdi mb with TCU

The diagram need external 12V power. must follow the diagram . Some EGS cable that customers buy from other website can not use with CGMB.

Read TCU information

Read TCU info success

Press Get to get erase password

Calculate erase password successfully.

Press Erase to reset

Erase TCU success
Read information again

TCU has been reset.

 

Note:

The EGS status , if "personalized " option not marked , "Activated " option marked,  the EGS has been erased by other tool . This status may will cause erase failure . you need to put it back to car to activate it first ,or use other tool to activate it . Then use CGMB to erase .

After software show you ''erased successfully " , you need to read the EGS status to check if it correct erase . if not , reboot your cgdi ,do it again

If erase password can not calculate , send your file to CG tech support .They can help you to calculate

After you erased succeed , install TCU back to car, need synchronize with autel, mb star diagnosis etc

CGDI Prog MB Software V3.0.5.0 Update Feature

 CGDI Prog MB software update to V3.0.5.0 (21/11/2020)

CGDI MB V3.0.5.0

1. Added the function of activating the new BGA key;
   2. Improved the function of reading the new BGA key;
   3. Improved W204/212, W221 dashboard mileage repair function.
   4. Optimized the mileage repair function interface;
   5. Optimized the 639 CAN all key lost collection eis data function;
   6. Fixed the problem that some W216 eis failed to read;

Solved! CG Pro “No found key” Problem

Here's the engineer solution to CG pro 9s12 programmer can not detect the key chip and shows error “No found key”.

 

1, First remove the cover with coil of the cg-pro, and place it as shown in the picture below. And then try to write key.

2. Write key follow cg pro prompts, if still not working, try to put the chip into these places marked red below

3. Avoid touching the coil position by hand and keep the equipment stable during operation
4. Install the cgpro cover after finishing the operation.
Note: Do not break the coil. 

If problem exists, customers can try to buy and replace a L4 inductor on the CG-PRO motherboard which locates in the lower right of the USB interface.

This is old one

This is new one
Inductance model: SHC0603-470m, patch 0603

https://www.obdii365.com/service/solve-cg-pro-no-found-key-error.html

CGDI MB W205 W222 W447 FBS4 Cluster Version List

Question before starting: 

Does CGDI MB support Mercedes FBS4 W447 cluster mileage reset?

Solution: 

Yes. But not all W447 cluster versions.

Check CGDI Prog MB supported Mercedes FBS4 instrument cluster type list.

Chassis	Mileage Repair Method	Instrument Cluster Version
W205	Software Filter Version	2059023013 2059023103 2059024618 2059025708 2059028308 2059028411 2059028504 2059028711 2059028817 2059029414 2059029514
	Hardware Filter Version	2059021304 2059022204 2059024001 2059024803 2059026002 2059028700 2059029614 2059029704
	Restore Factory Setting Version	2059021419 2059024318 2059026418
W222	Software Filter Version	2229021310 2229022310 2229022610 2229023515 2229026114 2229028210 2229029511
W447	Software Filter Version	4479023804 4479024005 4479026202 4479026604
	Hardware Filter Version	4479024006 4479024202 4479026904 4479029506
Note: Dash Chip R7F701414 is not supported currently.

*The cluster version is modified till June 2020. Keep updating more versions in the feature.

Note:

1).

FBS4 mileage repair license and extend adapter is required in order to repair mileage for MB FBS4 cluster.

2).

How to Check FBS4 cluster version?

The instrument version can be judged by the P2 position version of the instrument before year 2018.

Read also:  How to Repair Mercedes W205 FBS4 Mileage with CGDI MB?